which of the following is a type of machine safeguarding punching

Types of Safeguarding Devices 13 List of Figures Figure 1. 4206 SAFEGUARDING THE POINT OF OPERATION.

Machine Guarding 101 The Basics Kha Online Sds Management

The Occupational Safety and Health Administrations OSHAs requirements for machine guarding are found in 29 Code of Federal Regulations CFR 1910 Subpart O Machinery and Machine Guarding as detailed below.

. Feeding and ejection methods. Point of operation the area of a machine where it performs work on material. Hazardous Mechanical Motions and Actions.

The following types of mechanical components present amputation hazards. Must prevent workers from lubricating a machine without removing the safeguard. Good machine safeguarding makes it very difficult for anyone to be exposed to the danger zone.

Also asked is punching a type of machine safeguarding. Electromechanical sensing device on eye-letter machine. When the slideram is up the operator is allowed access to the point of operation.

Which is the following is not a requirement for safeguards. Punching action results when power is applied to a slide ram for the purpose of blanking drawing or stamping metal or other materials. The danger of this type of action occurs at the point of operation where stock is inserted held and withdrawn by hand.

Area on a machine where the work is performed. Which of the following is a type of machine safeguarding. In-Running Nip Points 8 Figure 9.

Most usable machine guards are described below. Must prevent workers from lubricating a machine without removing the safeguard. Which of the following is an exception to the general rule for safeguarding to prevent hazards during servicing and maintenance of machines.

The purpose of machine guarding is to protect the machine operator and other employees in the work area from hazards created during the machines normal operation. Reciprocating Motion 7 Figure 3. Any part of a machine which ___ while in operation can cause a hazard.

The following are all machine safeguarding requirements except. Primary Safeguarding Methods Two primary methods are used to safeguard machines. Machines can cause a variety of injuries ranging from minor abrasions burns or cuts to severe injuries such as fractures lacerations crushing injuries or even amputation.

Pullback devices utilize a series of cables attached to the operators hands wrists andor arms and are primarily used on machines with stroking action. Power-transmission apparatuses flywheels pulleys belts chains couplings spindles cams and gears in addition to connecting rods and other machine components that transmit. Examples of dangerous cutting hazards.

Which of the following is a type of machine safeguard. This would include hazards of concern such as. 2 Fixed limited access guards.

Commonly Used Machine Guards 12 Table 2. Punching action results when power is applied to a. OSHA Quiz 8 Machine Guarding.

The employer shall provide and ensure the use of properly applied and adjusted point of operation devices or guards for every operation performed on a. Pull outs Restraints. Guards and some types of safeguarding devices.

Typical machines used for punching operations are power presses and ironworker machines. Transversing Motion 7 Figure 4. Various types of machine guards available for machine guarding.

Crushed hands and arms severed fingers blindness -- the list of possible machinery-related injuries is as long as it is horrifying. Ingoing nip points rotating parts reciprocating transversing andor flying chips sparks. Cutting Action 7 Figure 5.

Guards provide physical barriers that prevent access to danger areas. Machine guards are your first line of defense against injuries. 3 Fixed adjustable access guard.

Which of the following is a type of machine safeguarding. Punching Action 8 Figure 6. Each piece of machinery has its own unique mechanical and non-mechanical hazards.

A Punching b Feeding and ejection methods c Point of operation d In-going nip points. Rotating Motion 7 Figure 2. Servicing or maintenance is not hazardous for employees b Maintenance is minimal and performed as an important part of production c Employer uses other safeguards which provide effective protection as required.

Which of the following is an exception to the general rule for safeguarding to prevent hazards during servicing and maintenance of machines. There seem to be as many hazards created by moving machine parts as there are types of machines. Which of the following is a type of machine safeguarding.

The following are all machine safeguarding requirements except. Their suitability should be selected. Machine safeguarding helps protect workers from preventable injuries in all three areas.

Two Hand controls Two hand Trip. A wide variety of mechanical motions and actions may present hazards to the operator. These can include the movement of rotating members reciprocating arms moving belts meshing gears cutting teeth.

Bending Action 8 Figure 8. Shearing Action 8 Figure 7. The 5 most common ways of machine guarding.

Which of the following is a type of machine safeguarding. Contents hide 1 Fixed guards. A Punching B Feeding and Ejection methods C Poinit of operation D In-going nip points Question.

Machine Guard Basics